Learn more about our product features:
 
 

Grablink Duo

Framegrabber für Camera Link-Kameras mit 1 Full-Konfiguration oder 2 Base-Konfigurationen

Im Überblick
  • Für zwei unabhängige Camera Link-Kameras mit Base-Konfiguration oder eine Camera Link-Kamera mit Base-, Medium-, Full-, 72-Bit- oder 80-Bit-Konfiguration
  • Direkt mit Hunderten von auf dem Markt erhältlichen CameraLink-Kameras kompatibel
  • PoCL (Power over Camera Link)
  • ECCO: Erweiterte CameraLink-Kabellänge
  • PCIe Gen 2 x4 Bus
  • Umfassende Funktionen mit 20 digitalen I/O-Leitungen
  • Kompatibel mit eGrabber-Treiber und Memento Event-Logging-Tool



Vergleichen Händler


Kompatibel mit <a target="_blank" href="https://www.euresys.com/en/Products/Machine-Vision-Software/eGrabber"target="_blank">eGrabber</A>
Kompatibel mit eGrabber


High-Performance DMA (Direct Memory Access)
High-Performance DMA (Direct Memory Access)

  • Direkte Übertragung an vom Benutzer zugewiesene Arbeitsspeicher- und Hardwarekarten, die PCI-Adressen bereitstellen
  • Hardware Scatter-Gather-Unterstützung
  • 64-Bit-Adressierungsfähigkeit


Trigger-Fähigkeiten 2/2 für Zeilenscans

  • Der Grablink-Framegrabber steuert die Abtastrate der Kamera anhand von Signalen, die er von einem Bewegungsencoder empfängt. Wenn sich Teile schneller bewegen, erhöht sich die Zeilenerfassungsrate der Kamera. Wenn sich Teile langsamer bewegen, verringert sich die Zeilenerfassungsrate der Kamera.
  • Die Grablink-Karten interpretieren A/B-Signale von Quadratur-Bewegungsencodern, um die Richtung (vorwärts oder rückwärts) des sich bewegenden Teils zu ermitteln.
  • Optional kann der Grablink angewiesen werden, Zeilen nur dann zu erfassen, wenn sich das Objekt vorwärts bewegt oder nur dann, wenn es sich rückwärts bewegt.
  • Die sogenannte Funktion „ Backward Motion Cancellation“ unterbricht die Erfassung, wenn eine Rückwärtsbewegung erkannt wird. Die Zeilenerfassung wird automatisch fortgesetzt, wenn sich die Bewegung wieder in die Vorwärtsrichtung ändert, und zwar genau an der Stelle, wo die Erfassung unterbrochen wurde.
  • Mit einem Rate Converter kann die Kamera Zeilen erfassen, die eine programmierbare niedrigere oder höhere Auflösung als die Auflösung des Bewegungsencoders haben. Dies gibt dem Designer während der Entwicklung der Anwendung unglaublich viel Spielraum und Flexibilität.
  • Mit einem Rate Divider kann die Kamera Zeilen mit einer niedrigeren Auflösung als die des Bewegungsencoders erfassen. Er teilt die Frequenz des eingehenden Encodersignals mit einer programmierbaren ganzen Zahl.


Universelle I/O-Leitungen
Universelle I/O-Leitungen

  • Kompatibel mit einer breiten Palette an Sensoren und Bewegungsencodern
  • Acht getrennte Strommesseingänge (bis zu 30 V, Signalgebung bis zu 200 kHz, einzeln galvanisch getrennt bis zu 250 VDC und 170 VAC RMS)
  • Vier Highspeed-Differenzeingänge (Unterstützung von Quadratur-Bewegungsencoder bis zu 5 MHz)
  • Vier galvanisch getrennte Kontaktausgänge (bis zu 30 V, 100 mA, Signalgebung bis zu 100 kHz)
  • Vier 5V-konforme Highspeed-TTL-Eingänge/-LVTTL-Ausgänge (Signalgebung bis zu 5 MHz)


Kompatibel mit Genicam
Kompatibel mit Genicam

Umfasst Support für

  • GenApi
  • Die Standard Feature Naming Convention (SFNC)
  • GenTL


<a target="_blank" href="https://www.euresys.com/ecco" >ECCO</a>: Erweiterter CameraLink-Kabeleinsatz
ECCO: Erweiterter CameraLink-Kabeleinsatz

  • Verwenden Sie längere Camera Link-Kabel (bis zu 15 Meter lang)!


Trigger-Fähigkeiten für Flächenscans

  • Wenn sich das Teil in seiner Position befindet, wird die Erfassung mithilfe eines Triggers ausgelöst. Hardware-Trigger kommen von den Grablink I/O-Leitungen. Software-Trigger kommen von der Anwendung.
  • Eine optionale Triggerverzögerung ist verfügbar, um die Erfassung entsprechend einer programmierbaren Zeit zu verschieben.
  • Eine Funktion zur Dezimierung von Triggern ermöglicht das Überspringen einiger Trigger.
  • Mit der Belichtungssteuerung der Kamera kann die Anwendung die Belichtungszeit der Kamera steuern.
  • Nach Beginn der Erfassung generiert die Grablink-Karte zum entsprechenden Zeitpunkt ein Signal, das ein an die Ausgangsleitung angeschlossenes Beleuchtungsgerät steuert.


Line-scan Metadata insertion
Line-scan Metadata insertion

When activated, this feature records metadata beside image data. Line metadata are captured every acquired image line. Buffer metadata are only captured when the first image line of a buffer is acquired. The metadata are composed with a configurable set of general purpose event counters, quadrature encoder position counters and/or I/O line status. This feature allows line-scan applications to correlate image data with system events including motion encoder positions.


Memento Event-Logging-Tool

  • Memento ist ein fortschrittliches Entwicklungs- und Debugging-Tool, das für Coaxlink- und Grablink-Karten verfügbar ist.
  • Memento zeichnet genaue Protokolle aller mit der Kamera, dem Framegrabber und seinen zugehörigen Treibern sowie der Anwendung im Zusammenhang stehenden Ereignisse auf.
  • Es liefert Entwicklern eine präzise Zeitachse der zeitgestempelten Ereignisse mit Kontextinformationen einer Logikanalysatoransicht.
  • Es bietet wertvolle Hilfe bei der Anwendungsentwicklung und beim Debuggen sowie während des Maschinenbetriebs.


Windows-, Linux- und Mac OS-Treiber verfügbar
Windows-, Linux- und Mac OS-Treiber verfügbar

  • Einschließlich Unterstützung für Intel 64-Bit-Plattformen sowie ARM 64-Bit-Plattformen


Direkt mit Hunderten von auf dem Markt erhältlichen CameraLink-Kameras kompatibel
Direkt mit Hunderten von auf dem Markt erhältlichen CameraLink-Kameras kompatibel

Sehen Sie sich unsere Seite mit unterstützten Kameras an (im Menü „Support“ unter „Unterstützte Kameras“)


Trigger-Fähigkeiten 1/2 für Zeilenscans

Grablink unterstützt die kontinuierliche Abtastung von Endlosmaterialien (um endlose, sich kontinuierlich bewegende Oberflächen zu prüfen, ohne eine einzige Zeile auszulassen) und die Abtastung einzelner Objekte (um das Bild von Objekten zu erfassen, die sich vor der Kamera bewegen).

  • Wenn sich das Teil in seiner Position befindet, wird die Erfassung mithilfe eines Triggers ausgelöst. Hardware-Trigger kommen von den I/O-Leitungen der Karte. Software-Trigger kommen von der Anwendung.
  • Nach dem Start wird die Erfassung mit einer der folgenden Optionen fortgesetzt:
    • Unendlich (für Web-Inspektionsanwendungen)
    • Eine programmierbare Anzahl an Zeilen (um das Bild von Objekten mit bekannter Länge zu erfassen)
    • Bis ein End-Trigger empfangen wird (um das Bild von Objekten mit variabler Länge zu erfassen)
  • Eine optionale Triggerverzögerung ist verfügbar, um den Beginn der Erfassung entsprechend einer programmierbaren Anzahl an Zeilen zu verschieben.


Flexible Zeilenkamera-Anwendung mit einem Rate Converter

  • Der Rate Converter ist ein intelligenter, programmierbarer Frequenzvervielfacher/-teiler.
  • Wird mit Bewegungsencodern und Zeilenkameras verwendet und ermöglicht dem Anwender das Seitenverhältnis der Pixel im Bild auszuwählen.
  • Er bietet eine Möglichkeit, die Erfassungskette so zu kalibrieren, dass problemlos quadratische Pixel (Seitenverhältnis von 1:1) erreicht werden.


Synchronisation von Kameras mit <a target="_blank" href="https://www.euresys.com/en/Landing-Pages/C2C-Link"target="_blank">C2C-Link</a>
Synchronisation von Kameras mit C2C-Link

Ermöglicht die genaue Synchronisation von mehreren angeschlossenen Flächen- und Zeilenkameras

  • mit derselben Karte
  • mit verschiedenen Karten auf demselben PC
  • mit verschiedenen Karten in verschiedenen PCs


Mechanical
Format Standard profile, half length, 4-lane PCI Express card
Cooling method Air cooling, fan-cooled heatsink
Mounting For insertion in a standard height, 4-lane or higher, PCI Express card slot
Connectors
  • 'A' on bracket:
    • 26-position Shrunk Delta Ribbon (SDR) socket
    • Camera Link camera #1 Base connector
  • 'B' on bracket:
    • 26-position Shrunk Delta Ribbon (SDR) socket
    • Camera Link camera #1 Medium/Full/72-bit/80-bit connector
    • Camera Link camera #2 Base connector
  • 'EXTERNAL I/O' on bracket:
    • 26-pin 3-row high-density female sub-D connector
    • I/O lines and power output
  • 'INTERNAL I/O 1' on PCB:
    • 26-pin 2-row 0.1" pitch pin header with shrouding
    • I/O lines and power output
  • 'INTERNAL I/O 2' on PCB:
    • 26-pin 2-row 0.1" pitch pin header with shrouding
    • I/O lines and power output
  • 'I/O EXTENSION' on PCB:
    • 26-pin 2-row 0.05" pitch pin header with shrouding
    • I/O extension lines and power output
  • 'AUXILIARY POWER INPUT' on PCB:
    • 6-pin PEG power socket
    • 12 VDC power input for PoCL camera(s) and I/O power output
  • 'C2C-LINK' on PCB:
    • 6-pin 2-row 0.1-in header
    • Card to card link
LED indicators
  • 'A', 'B' on bracket:
    • Bi-color red/green LEDs
    • Camera Link status indicator
Switches 'RECOVERY' on PCB:
  • 3-pin 1-row 0.1" header or 2-way DIP switch
  • Firmware emergency recovery
Dimensions PCB L X H: 167.65 mm x 111.15 mm, 6.6 in x 4.38 in
Weight 150 g, 5.29 oz
Host bus
Standard PCI Express 2.0
Link width
  • 4 lanes
  • 1 lane or 2 lanes with reduced performance
Link speed
  • 5.0 GT/s (PCIe 2.0)
  • 2.5 GT/s (PCIe 1.0) with reduced performance
Maximum payload size 512 bytes
Peak delivery bandwidth 2,000 MB/s
Effective (sustained) delivery bandwidth 1,700 MB/s (Host PC motherboard dependent)
Power consumption Typ. 7.1 W ( 2.7 W @ +3.3V, 4.4 W @ +12V), excluding camera and I/O power output
Camera / video inputs
Interface standard(s) Camera Link 2.0
Connectors Two Shrunk Delta Ribbon (SDR) Miniature Camera Link (MiniCL)
ECCO - Extended Camera Link Cable Operation ECCO
Number of cameras
  • One 80-bit / 72-bit / Full / Medium / Base configuration camera
  • Or two Base configuration cameras
Maximum aggregated camera data transfer rate 6.8 Gbit/s (850 MB/s)
Camera Link configuration Base, Medium, Full, 72-bit, 80-bit
Camera Link clock frequency From 20 MHz up to 85 MHz
PoCL (Power over Camera Link)
  • PoCL Safe Power:
    • Two independent controllers
    • PoCL Device detection and automatic power-on
    • Overload and short-circuit protection
  • A +12V power source must be connected to the AUXILIARY POWER INPUT connector using a 6-pin PEG cable
Camera types
  • Area-scan cameras:
    • Grayscale and color (RGB and Bayer CFA)
  • Line-scan cameras:
    • Grayscale and color RGB
Camera pixel formats supported
  • Mono8, Mono10, Mono12, Mono14, Mono16
  • BayerXX8, BayerXX10, BayerXX12, BayerXX16 where XX = GR, RG, GB, or BG
  • RGB8
NOTE: Refer to release notes for availability of BayerXX14, RGB10, RGB12, RGB14 and RGB16 formats
Area-scan camera control
Trigger
  • Precise control of asynchronous reset cameras, with exposure control.
  • Support of camera exposure/readout overlap.
  • Support of external hardware trigger, with optional delay and trigger decimation.
Strobe
  • Accurate control of the strobe position for strobed light sources.
  • Support of early and late strobe pulses.
Line-scan camera control
Scan/page trigger
  • Precise control of start-of-scan and end-of-scan triggers.
  • Support of external hardware trigger, with optional delay.
  • Support of infinite acquisition, without missing line, for web inspection applications.
Line trigger
  • Support for quadrature motion encoders, with programmable noise filters, selection of acquisition direction and backward motion compensation.
  • Rate Converter tool for fine control of the pixel aspect ratio: Rate Conversion Ratio in the range 0.001 to 1000 with an accuracy better than 0.1%.
  • Rate Divider tool
Line strobe
  • Accurate control of the strobe position for strobed light sources.
On-board processing
On-board memory 512 MB
Image data stream processing
  • Unpacking of 10-/12-/14-bit to 16-bit with selectable justification to LSb or MSb
Input LUT (Lookup Table)
  • Monochrome 8-bit to 8-bit transformation
  • Monochrome 10-bit to 8-, 10- or 16-bit transformations
  • Monochrome 12-bit to 8-, 12- or 16-bit transformations
Bayer CFA to RGB decoder Advanced interpolation method using average and median functions on a 3x3 kernel
Data stream statistics
  • Measurement of:
    • Frame rate (Area-scan only)
    • Line rate
    • Data rate
  • Configurable averaging interval
Event signaling and counting
  • The application software can be notified of the occurrence of various events:
    • Standard event: the EVENT_NEW_BUFFER event notifies the application of newly filled buffers
    • A large set of custom events
  • Custom events sources:
    • I/O Toolbox events
    • Camera and Illumination control events
  • Each custom event is associated with a 32-bit counter that counts the number of occurrences
  • The last three 32-bit context data words of the event context data can be configured with event-specific context data:
    • Event-specific data
    • State of all System I/O lines sampled at the event occurrence time
    • Value of any event counter
Metadata Insertion Recording of metadata beside image data.
  • The metadata are composed with a configurable set of general purpose event counters, quadrature encoder position counters and/or I/O line status.
  • Line metadata are captured every acquired image line.
  • Buffer metadata are only captured when the first image line of a buffer is acquired.
  • Allows line-scan applications to correlate image data with system events including motion encoder positions.
NOTE: Only available on selected line-scan firmware variants. Refer to release notes.
General Purpose Inputs and Outputs
Number of lines 20 I/O lines:
  • 4 differential inputs (DIN)
  • 4 singled-ended TTL inputs/outputs (TTLIO)
  • 8 isolated inputs (IIN)
  • 4 isolated outputs (IOUT)
NOTE: The number of I/O lines can be extended using I/O modules attached to the I/O EXTENSION connector.
Usage
  • Any I/O input lines can be used by any LIN tool of the I/O Toolbox
  • Selected pairs of I/O input lines can be used by any QDC tool of the I/O toolbox to decode A/B signals of a motion encoder
Electrical specifications
  • DIN: High-speed differential inputs, up to 5 MHz, compatible with ANSI/EIA/TIA-422/485 differential line drivers and complementary TTL drivers
  • TTLIO: High-speed 5V-compliant TTL inputs or LVTTL outputs, compatible with totem-pole LVTTL, TTL, 5V CMOS drivers or LVTTL, TTL, 3V CMOS receivers
  • IIN: Isolated current-sense inputs with wide voltage input range up to 30V, signaling up to 200 kHz, individual galvanic isolation up to 250VDC and 170 VAC, compatible with totem-pole LVTTL, TTL, 5V CMOS drivers, RS-422 differential line drivers, potential free contacts, solid-state relays and opto-couplers
  • IOUT: Isolated contact outputs compatible with 30V / 100mA loads
NOTE: IIN and IOUT lines provide a functional isolation grade for the circuit technical protection. It does not provide an isolation that can protect a human being from electrical shock!
Filter control
  • Glitch removal filter available on all System I/O input lines
  • Configurable filter time constants:
    • for DIN and TTLIO lines: 50 ns, 100 ns, 200 ns, 500 ns, 1 µs
    • for IIN lines: 500 ns, 1 µs, 2 µs, 5 µs, 10 µs
Polarity control Yes
Power output Non-isolated, +12V, 1A, with electronic fuse protection
I/O Toolbox tools The I/O Toolbox is a configurable interconnection of tools that generates events (usually triggers):
  • Line Input tool (LIN): edge detector delivering events on rising or falling edges of any selected input line.
  • Quadrature Decoder tool (QDC): a composite tool including:
    • A quadrature edge detector delivering events on selected transitions of selected pairs of input lines.
    • An optional backward motion compensator for clean line-scan image acquisition when the motion is unstable.
    • A 32-bit up/down counter for delivering a position value.
  • User Actions Scheduler tool (UAS): to delegate the execution of 'User Actions' at a scheduled time or encoder position. Possible user actions include setting low/high/toggle any bit of the User Output Register or generation of any User Events.
  • Delay tool (DEL): to delay up to 16 events from one or two I/O toolbox event sources, by a programmable time or number of motion encoder ticks (any QDC events).
  • Divider tool (DIV): to generate an event every nth input events from any I/O toolbox event source.
  • Multiplier/divider tool (MDV): to generate m events every d input events from any I/O toolbox event source.
  • The 'Input Tools' (LIN, QDC and UAS) can be further processed by the 'Event Tools' (DEL, DIV and MDV) to generate any of the following "trigger" events:
    • The "cycle trigger" of the Camera and Illumination controller
    • The "cycle sequence trigger" of the Camera and Illumination controller
    • The "start-of-scan trigger" of the Acquisition Controller (line-scan only)
    • The "end-of-scan trigger" of the Acquisition Controller (line-scan only)
I/O Toolbox composition Determined by the selected firmware variant:
  • '1-camera': 8 LIN, 1 QDC, 1 UAS, 2 DEL, 1 DIV, 1 MDV, 2 C2C
  • '2-camera': 8 LIN, 2 QDC, 1 UAS, 2 DEL, 2 DIV, 2 MDV, 2 C2C
  • '1-camera, line-scan': 8 LIN, 1 QDC, 1 UAS, 2 DEL, 1 DIV, 1 MDV, 3 C2C
  • '2-camera, line-scan': 8 LIN, 2 QDC, 1 UAS, 2 DEL, 2 DIV, 2 MDV, 3 C2C
C2C-Link
Description
  • Accurate synchronization of the trigger and the start-of-exposure of multiple grabber-controlled area-scan cameras.
  • Accurate synchronization of the start-of-cycle, start-of-scan and end-of-scan of multiple grabber-controlled line-scan cameras.
Specification
  • C2C-Link synchronizes cameras connected to:
    • the same card
    • to different cards in the same PC (requires an accessory cable such as the "3303 C2C-Link Ribbon Cable" or a custom-made C2C-Link cable)
    • to different cards in different PCs (requires one "1636 InterPC C2C-Link Adapter" for each PC and one RJ 45 CAT 5 STP straight LAN cable for each adapter but the last one)
  • Maximum distance:
    • 60 cm inside a PC
    • 1200 m cumulated adapter to adapter cable length
  • Maximum trigger rate:
    • 2.5 MHz for configurations using a single PC, or up to 10 PCs and 100 m total C2C-Link cable length
    • 200 kHz for configurations up to 32 PCs and 1200m total C2C-Link cable length
  • Trigger propagation delay from master to slave devices:
    • Less than 10 ns for cameras on the same card or on different cards in the same PC
    • Less than 265 ns for cameras on different cards in different PCs (3 PCs and 40m total C2C-Link cable length)
Software
Host PC Operating System
  • Microsoft Windows 11, 10, 8.1, 7 for x86-64 (64-bit) processor architecture
  • Linux for x86-64 (64-bit) and AArch64 (64-bit) processor architectures
  • macOS for x86-64 (64-bit) and AArch64 (64-bit) processor architectures
APIs
  • EGrabber class, with C++ and .NET APIs: .NET assembly designed to be used with development environments compatible with .NET frameworks version 4.0 or higher
  • GenICam GenTL producer libraries compatible with C/C++ compilers:
    • 'x86_64' dynamic library designed to be used with ISO-compliant C/C++ compilers for the development of x86-64 (64-bit) applications
    • 'aarch64' dynamic library designed to be used with ISO-compliant C/C++ compilers for the development of AArch64 (64-bit) applications
Environmental conditions
Operating ambient air temperature 0 °C to +50 °C / +32 °F to +122 °F
Operating ambient air humidity 10% to 90% RH non-condensing
Storage ambient air temperature -20 °C to +70 °C/ -4 °F to +158 °F
Storage ambient air humidity 10% to 90% RH non-condensing
Certifications
Electromagnetic - EMC standards
  • European Council EMC Directive 2014/30/EU
  • United States FCC rule 47 CFR 15
EMC - Emission
  • EN 55032:2015 / CISPR 32:2012 Class B
  • FCC 47 Part 15 Class B
EMC - Immunity
  • EN 55035:2017 / CISPR 35:2016
  • EN 61000-6-2:2005 / IEC 61000-6-2:2016
  • EN 61000-4-2:2009
  • EN 61000-4-3:2006
  • EN 61000-4-4:2004
  • EN 61000-4-6:2014
KC Certification Korean Radio Waves Act, Article 58-2, Clause 3
Flammability PCB compliant with UL 94 V-0
RoHS European Union Directive 2015/863 (ROHS3)
REACH European Union Regulation 1907/2006
WEEE Must be disposed of separately from normal household waste and must be recycled according to local regulations
Ordering Information
Product code - Description
Optional accessories
HS Acquisition

Highspeed-Bilderfassung für AOI-, 3D SPI-, 3D Lead/Ball-Inspektionssysteme.

Die Coaxlink- und Grablink-Karten sind zuverlässige industrielle Framegrabber, die eine robuste und stabile Bilderfassung von den schnellsten Digitalkameras auf dem Markt ermöglichen. Sie liefern präzise Kamerasteuerungs- und Synchronisierungsfunktionen.
  • AOI-Systeme (automatische optische Inspektion, engl. Automated Optical Inspection)
  • 3D-SPI-Systeme (Lotpasteninspektion, engl. Solder Paste Inspection)
  • 3D-Lead-/Ball-Inspektionssysteme
LS Acquisition Elec

Line-Scan-Bilderfassung mit sehr hoher Auflösung für Flachbildschirminspektion und Solarzelleninspektion

Die Coaxlink- und Grablink-Karten sind zuverlässige industrielle Framegrabber, die eine robuste und stabile Bilderfassung von den schnellsten Digitalkameras auf dem Markt ermöglichen. Sie liefern präzise Zeilenkamerasteuerungs- und Synchronisierungsfunktionen.
LS Acquisition Man

Line-Scan-Bilderfassung für Oberflächeninspektionssysteme

Die Coaxlink- und Grablink-Karten sind zuverlässige industrielle Framegrabber, die eine robuste und stabile Bilderfassung von den schnellsten Digitalkameras auf dem Markt ermöglichen. Sie liefern präzise Zeilenkamerasteuerungs- und Synchronisierungsfunktionen.
LS Acquisition Textile

Line-Scan-Bilderfassung für Textilinspektionen

Die Coaxlink- und Grablink-Karten sind zuverlässige industrielle Framegrabber, die eine robuste und stabile Bilderfassung von den schnellsten Digitalkameras auf dem Markt ermöglichen. Sie liefern präzise Zeilenkamerasteuerungs- und Synchronisierungsfunktionen.