eGrabber 24.06
- eGrabber Gigelink 新增了多播支持,可以实现一对多图像数据流传输。
- Playlink:Euresys 新推出的一种 GenTL 生成器,用于回放记录器中的图像,其效果好比这些图像直接来自远程设备一样。
- 为 Coaxlink 和 Grablink Duo 的数据流 StripeArrangements 增添了新的几何形状和命令。
- 生产力方面实现了多项改进。
- 为 Cognex VisionPro 软件增添了 eGrabber 适配器
四路 CoaXPress-over-Fiber 采集卡
© EURESYS S.A. - Subject to change without notice
8/14/2024 Datasheet 四路 CoaXPress-over-Fiber 采集卡
Main benefitsOther benefits规格Mechanical
Host bus
Camera / video inputs
Area-scan camera control
Line-scan camera control
On-board processing
General Purpose Inputs and Outputs
C2C-Link
Software
Environmental conditions
Certifications
Ordering Information
Offices
|
CoaXPress (CXP)是业界高带宽计算机视觉应用标准。最新版CoaXPress 2.1规范中规定了CXP-12速度,即通过同轴铜缆进行12.5 Gbps(千兆位每秒)连接。
由于链路聚合在CoaXPress中很常见,因此四路CXP-12连接可以轻松实现50 Gbps (12.5 x 4)的带宽。CoaXPress-over-Fiber是CoaXPress规范的附加部分。它提供了一种通过标准以太网连接(包括光纤)运行未经修改的CoaXPress协议的方法。因此,CoaXPress-over-Fiber使用为以太网设计的标准电子设备、连接器和电缆,但所采用的协议既不是以太网,也不是GigE Vision,而是CoaXPress。
PCI Express card
Standard profile, half length, 8-lane PCI Express card
Air cooling, fan-cooled heatsink
For insertion in a standard height, 8-lane or higher, PCI Express card slot
'QSFP+' on card bracket:
Enhanced Quad Small Form-factor Pluggable port
CoaXPress-over-Fiber Host Interface
'EXTERNAL I/O' on card bracket:
26-pin 3-row high-density D-Sub female socket with UNC4-40 jack socket screws
I/O lines and I/O power output
'INTERNAL I/O 1' on printed circuit board:
26-pin 2-row 0.1" pitch pin header with shrouding
I/O lines and I/O power output
'INTERNAL I/O 2' on printed circuit board:
26-pin 2-row 0.1" pitch pin header with shrouding
I/O lines and I/O power output
'I/O EXTENSION' on printed circuit board:
26-pin 2-row 0.05" pitch pin header with shrouding
I/O extension cable socket
'C2C-LINK' on printed circuit board:
6-pin 2-row 0.1" pitch pin header with shrouding
Card-to-card link
'AUXILIARY POWER INPUT' on printed circuit board:
6-pin PEG power socket
12 V DC power input for I/O power output
'A', 'B', 'C', 'D' on bracket:
Bi-color red/green LEDs
CoaXPress Host connector indicator
'FPGA STATUS LAMP' on PCB:
Bi-color red/green LED
FPGA status indicator
'BOARD STATUS LAMP' on PCB:
Bi-color red/green LED
Board status indicator
'RECOVERY' on PCB:
3-pin 1-row 0.1" header or 2-way DIP switch
Firmware emergency recovery
PCB L x H: 167.65 mm x 111.15 mm [6.6 in x 4.38 in]
Net weight: 178 g [6.3 oz]
Gross weight: 283 g [10 oz]
PCI Express 3.0
8 lanes
1 lane, 2 lanes or 4 lanes with reduced performance
8.0 GT/s (PCIe 3.0)
5.0 GT/s (PCIe 2.0) with reduced performance
512 bytes
32- and 64-bit
7,800 MB/s
6,700 MB/s (Host PC motherboard dependent)
Typ. 16.5 W ( 3.0 W @ +3.3V, 12.5 W @ +12V), excluding I/O power output and optical transceiver module
CoaXPress
CoaXPress 1.0, 1.1, 1.1.1 and 2.0, CoaXPress-over-Fiber Bridge Protocol 1.0
CXP-over-Fiber
4 connections
Enhanced Quad Small Form-factor Pluggable (QSFP+) port
Compliant with SFF-8436 (4 x10 Gbit/s Pluggable Transceiver) specification
Compliant with CoaXPress over Fiber
Available power for the module: 3.5 W (SFF-8436 Power Level 4)
One CoaXPress Host connection status LED per connection
Area-scan cameras:
One 1- or 2- or 4-connection camera
Line-scan cameras:
One 1- or 2- or 4-connection camera
1
Yes
5,000 MB/s
1.25 GT/s (CXP-1), 2.5 GT/s (CXP-2), 3.125 GT/s (CXP-3), 5 GT/s (CXP-5), 6.25 GT/s (CXP-6), 10.0 GT/s (CXP-10), and 12.5 GT/s (CXP-12)
Low-speed 20.83... Mbps (CXP-1 to CXP-6)
Low-speed 41.66... Mbps (CXP-10, CXP-12)
1 data stream per camera
16,384 bytes
Area-scan cameras:
Grayscale and color (YCbCr, YUV, RGB and Bayer CFA)
Single-tap (1X-1Y) progressive-scan
Line-scan cameras and contact imaging sensors:
Grayscale and color RGB
Mono8, Mono10, Mono12, Mono14, Mono16
BayerXX8, BayerXX10, BayerXX12, BayerXX14, BayerXX16 where XX = GR, RG, GB, or BG
RGB8, RGB10, RGB12, RGB14, RGB16
RGBA8, RGBA10, RGBA12, RGBA14, RGBA16
YCbCr601_422_8, YCbCr601_422_10
YCbCr709_422_8, YCbCr709_422_10
YUV422_8, YUV422_10
Raw
Precise control of asynchronous reset cameras, with exposure control.
Support of camera exposure/readout overlap.
Support of external hardware trigger, with optional delay and trigger decimation.
Accurate control of the strobe position for strobed light sources.
Support of early and late strobe pulses.
Precise control of start-of-scan and end-of-scan triggers.
Support of external hardware trigger, with optional delay.
Support of infinite acquisition, without missing line, for web inspection applications.
Support for quadrature motion encoders, with programmable noise filters, selection of acquisition direction and backward motion compensation.
Rate Converter tool for fine control of the pixel aspect ratio: Rate Conversion Ratio in the range 0.001 to 1000 with an accuracy better than 0.1%.
Rate Divider tool
Accurate control of the strobe position for strobed light sources.
4 GB
Unpacking of 10-/12-/14-bit to 16-bit with selectable justification to LSb or MSb
Optional swap of R and B components
Little endian conversion
Monochrome 8-bit to 8-bit transformation
Monochrome 10-bit to 8-, 10- or 16-bit transformations
Monochrome 12-bit to 8-, 12- or 16-bit transformations
'1-camera' firmware variant:
3x3 linear interpolation method
3x3 median-based interpolation method
Measurement of:
Frame rate (Area-scan only)
Line rate
Data rate
Configurable averaging interval
The application software can be notified of the occurrence of various events:
Standard event: the EVENT_NEW_BUFFER event notifies the application of newly filled buffers
A large set of custom events
Custom events sources:
I/O Toolbox events
Camera and Illumination control events
CoaXPress data stream events
CoaXPress host interface events
Each custom event is associated with a 32-bit counter that counts the number of occurrences
The last three 32-bit context data words of the event context data can be configured with event-specific context data:
Event-specific data
State of all System I/O lines sampled at the event occurrence time
Value of any event counter
20 I/O lines:
4 differential inputs (DIN)
4 singled-ended TTL inputs/outputs (TTLIO)
8 isolated inputs (IIN)
4 isolated outputs (IOUT)
NOTE: The number of I/O lines can be extended using I/O modules attached to the I/O EXTENSION connector.
Any I/O input lines can be used by any LIN tool of the I/O Toolbox
Selected pairs of I/O input lines can be used by any QDC tool of the I/O toolbox to decode A/B signals of a motion encoder
DIN: High-speed differential inputs, up to 5 MHz, compatible with ANSI/EIA/TIA-422/485 differential line drivers and complementary TTL drivers
TTLIO: High-speed 5V-compliant TTL inputs or LVTTL outputs, compatible with totem-pole LVTTL, TTL, 5V CMOS drivers or LVTTL, TTL, 3V CMOS receivers
IIN: 200 kHz isolated current-sense input with wide voltage input range up to 30V, compatible with totem-pole (push-pull) HTL drivers, 5V TTL/RS-422 differential line drivers, 5V CMOS drivers, potential free contacts, solid-state relays and opto-couplers
IOUT: Isolated contact outputs compatible with 30V / 100mA loads
NOTE: IIN and IOUT lines provide a functional isolation grade for the circuit technical protection. It does not provide an isolation that can protect a human being from electrical shock!
Glitch removal filter available on all System I/O input lines
Configurable filter time constants:
for DIN and TTLIO lines: 50 ns, 100 ns, 200 ns, 500 ns, 1 µs
for IIN lines: 500 ns, 1 µs, 2 µs, 5 µs, 10 µs
Yes
Non-isolated, +12V, 1A, with electronic fuse protection
The I/O Toolbox is a configurable interconnection of tools that generates events (usually triggers):
Line Input tool (LIN): edge detector delivering events on rising or falling edges of any selected input line.
Quadrature Decoder tool (QDC): a composite tool including:
A quadrature edge detector delivering events on selected transitions of selected pairs of input lines.
An optional backward motion compensator for clean line-scan image acquisition when the motion is unstable.
A 32-bit up/down counter for delivering a position value.
Device Link Trigger tool (DLT): delivers an event on reception of a valid high-speed CoaXPress 2.0 connection trigger packet message from the remote device.
User Actions Scheduler tool (UAS): to delegate the execution of 'User Actions' at a scheduled time or encoder position. Possible user actions include setting low/high/toggle any bit of the User Output Register or generation of any User Events.
Delay tool (DEL): to delay up to 16 events from one or two I/O toolbox event sources, by a programmable time or number of motion encoder ticks (any QDC events).
Divider tool (DIV): to generate an event every nth input events from any I/O toolbox event source.
Multiplier/divider tool (MDV): to generate m events every d input events from any I/O toolbox event source.
The 'Input Tools' (LIN, QDC, DLT and UAS) can be further processed by the 'Event Tools' (DEL, DIV and MDV) to generate any of the following "trigger" events:
The "cycle trigger" of the Camera and Illumination controller
The "cycle sequence trigger" of the Camera and Illumination controller
The "start-of-scan trigger" of the Acquisition Controller (line-scan only)
The "end-of-scan trigger" of the Acquisition Controller (line-scan only)
Determined by the selected firmware variant:
'1-camera': 8 LIN, 1 QDC, 2 DLT, 1 UAS, 2 DEL, 1 DIV, 1 MDV, 2 C2C
'1-camera, line-scan': 8 LIN, 1 QDC, 2 DLT, 1 UAS, 2 DEL, 1 DIV, 1 MDV, 3 C2C
Accurate synchronization of the trigger and the start-of-exposure of multiple grabber-controlled area-scan cameras.
Accurate synchronization of the start-of-cycle, start-of-scan and end-of-scan of multiple grabber-controlled line-scan cameras.
C2C-Link synchronizes cameras connected to:
the same card
to different cards in the same PC (requires an accessory cable such as the "3303 C2C-Link Ribbon Cable" or a custom-made C2C-Link cable)
to different cards in different PCs (requires one "1636 InterPC C2C-Link Adapter" for each PC and one RJ 45 CAT 5 STP straight LAN cable for each adapter but the last one)
Maximum distance:
60 cm inside a PC
1200 m cumulated adapter to adapter cable length
Maximum trigger rate:
2.5 MHz for configurations using a single PC, or up to 10 PCs and 100 m total C2C-Link cable length
200 kHz for configurations up to 32 PCs and 1200m total C2C-Link cable length
Trigger propagation delay from master to slave devices:
Less than 10 ns for cameras on the same card or on different cards in the same PC
Less than 265 ns for cameras on different cards in different PCs (3 PCs and 40m total C2C-Link cable length)
Microsoft Windows 11, 10, 8.1, 7 for x86-64 (64-bit) processor architecture
Linux for x86-64 (64-bit) and AArch64 (64-bit) processor architectures
macOS for x86-64 (64-bit) and AArch64 (64-bit) processor architectures
EGrabber class, with C++ and .NET APIs: .NET assembly designed to be used with development environments compatible with .NET frameworks version 4.0 or higher
GenICam GenTL producer libraries compatible with C/C++ compilers:
'x86_64' dynamic library designed to be used with ISO-compliant C/C++ compilers for the development of x86-64 (64-bit) applications
'aarch64' dynamic library designed to be used with ISO-compliant C/C++ compilers for the development of AArch64 (64-bit) applications
Yes
0 °C to +55 °C / +32 °F to +131 °F
10% to 90% RH non-condensing
-20 °C to +70 °C/ -4 °F to +158 °F
10% to 90% RH non-condensing
European Council EMC Directive 2014/30/EU
United States FCC rule 47 CFR 15
EN 55032:2015 / CISPR 32:2012 Class B
FCC 47 Part 15 Class B
EN 55035:2017 / CISPR 35:2016
EN 61000-6-2:2005 / IEC 61000-6-2:2016
EN 61000-4-2:2009
EN 61000-4-3:2006
EN 61000-4-4:2004
EN 61000-4-6:2014
Korean Radio Waves Act, Article 58-2, Clause 3
PCB compliant with UL 94 V-0
European Union Directive 2015/863 (ROHS3)
European Union Regulation 1907/2006
Must be disposed of separately from normal household waste and must be recycled according to local regulations
PC3625 Coaxlink QSFP+
PC1625 DB25F I/O Adapter Cable
PC1636 InterPC C2C-Link Adapter
PC3303 C2C-Link Ribbon Cable
PC3304 HD26F I/O Adapter Cable
PC3610 HD26F I/O Extension Module - TTL-RS422
PC3612 HD26F I/O Extension Module - TTL-CMOS5V-RS422
PC3613 JTAG Adapter Xilinx for Coaxlink
PC3629 Coaxlink CXP-12 to QSFP+ Converter
Coaxlink_NetApi.dll
assembly targets: